Capabilities and products
- maintenance and calibration of color, light-source, and weathering measurement equipment
- high-precision benchtop spectrophotometer supply (Konica Minolta)
- high-precision portable spectrophotometer supply (Konica Minolta)
- reflective, transmissive, and fluorescent-color spectrophotometer supply (Konica Minolta)
- 60° gloss measurement equipment supply (Konica Minolta)
- handheld chroma meter supply (Konica Minolta)
- HDR display color analyzer supply (Konica Minolta)
- non-contact luminance and color meter supply (Konica Minolta)
- spectroradiometer supply (Konica Minolta)
- illuminance meter supply (Konica Minolta)
- UV accelerated weathering tester supply (Q-LAB)
- xenon arc weathering test chamber supply (Q-LAB)
- cyclic corrosion tester supply (Q-LAB)
- hand coater supply (RK PrintCoat Instruments)
- controlled-speed-and-pressure laboratory coater supply (RK PrintCoat Instruments)
- gravure coating machine supply (RK PrintCoat Instruments)
- manual flexographic proofing equipment supply (RK PrintCoat Instruments)
- flexographic proofing press supply (RK PrintCoat Instruments)
Exhibits
PROCHEM PACIFIC CORPORATION offers the Konica Minolta CM-3700A Plus high-precision benchtop spectrophotometer for reference color measurement, establishing master color standards and digital color management across sites. The CM-3700A Plus measures reflectance and transmittance, records SCI and SCE simultaneously and supports LAV, LMAV, MAV and SAV measurement areas, electronic camera viewing and WAA wavelength analysis and adjustment. Under the specified conditions, its white repeatability is SD ΔEab ≤ 0.005, black repeatability SD ΔEab ≤ 0.02 and inter-instrument agreement ΔE*ab ≤ 0.08; the instrument also monitors ambient temperature, humidity and sample-surface temperature. Konica Minolta CM-17d and CM-16d portable spectrophotometers use d:8° geometry, selectable SCI/SCE modes and 0.7-second measurements for production inspection, color quality control and research. The CM-17d has Ø8 mm and Ø3 mm apertures with a camera viewfinder, while the CM-16d uses an Ø8 mm aperture; WLAN/Bluetooth communications require the optional CM-A300 module on both models. CM-17d color repeatability reaches SD ΔE*ab 0.02 and inter-instrument agreement ΔE*ab 0.12, compared with SD ΔE*ab 0.04 and ΔE*ab 0.20 for CM-16d under specified conditions. The Konica Minolta CM-36d, CM-36dG and CM-36dGV benchtop spectrophotometers use an integrating sphere with d/8 geometry and switchable measurement areas of Ø25.4, Ø16, Ø8 and Ø4 mm. These models measure reflective, transparent and fluorescent colors with SCI/SCE options and ultraviolet cut filters; CM-36dG and CM-36dGV also measure gloss at 60 degrees. The CR-400/410 handheld chroma meters measure surface color; the CR-400 uses an 8 mm aperture and can operate independently or with a data processor for advanced functions and on-site printing. The CS-3000HDR and CS-3000 spectroradiometers measure display luminance and chromaticity over ranges from very low to high brightness, including LCD, OLED, micro-LED and mini-LED displays. The CA-410 display color analyzer measures white balance, gamma and chromaticity for television and smartphone displays, including HDR and OLED models, and supports VESA DisplayHDR measurement requirements. For CIE 170-2 measurements, CA-P427C and CA-P410C probes provide Ø27 mm and Ø10 mm measurement diameters respectively, with acceptance angles of ±2.5° and ±5°. The non-contact CS-200 luminance and color meter measures luminous displays and light sources using 40 sensors, with selectable measurement angles of 1°, 0.2° and 0.1°. CS-200 presents color coordinates such as Lv xy, Lv u′v′, XYZ and dominant wavelength, and measures luminance down to 0.01 cd/m² or up to 20,000,000 cd/m² at the 0.1° measurement angle. The battery-powered CS-150 and CS-160 non-contact luminance and color meters measure lamps, signals, projected images and surfaces unsuitable for physical contact, with 1° and one-third-degree measurement angles respectively. The CS-150 luminance range extends to 999,900 cd/m² and the CS-160 to 9,999,000 cd/m², and the instruments offer chromaticity-difference measurements. The T-10A and T-10MA illuminance meters support LED and PWM-controlled light sources, conform to JIS AA and DIN B classes and offer measurement for lighting inspection and maintenance. The T-10A displays illuminance and average values from 0.01 to 299,000 lx and supports detachable detector heads and multi-point measurement configurations. Q-LAB QUV accelerated weathering testers expose samples to fluorescent ultraviolet light and high-temperature condensation cycles to reproduce outdoor sunlight and dew damage such as color change, gloss loss, cracking, blistering and embrittlement. QUV systems use fluorescent UV lamps for short-wavelength exposure and a condensation system that evaporates and condenses ordinary tap water onto test specimens. The Q-LAB Q-SUN Xe-3 xenon-arc chamber uses three separate xenon lamps and a slide-out 451 × 718 mm specimen tray to simulate full-spectrum sunlight and rain for lightfastness, colorfastness and photostability testing. Xe-3 configurations provide humidity control as standard and optional front or rear spray, dual-spray functions and chillers for different exposure conditions. Q-LAB Q-FOG SSP and CCT cyclic corrosion chambers perform conventional salt-spray, Prohesion and most automotive cyclic corrosion tests to simulate outdoor atmospheric corrosion. The Q-FOG SSP-600 and SSP-1100 support salt spray and Prohesion, while CCT-600 and CCT-1100 also add 100% humidity control; chamber volumes are 640 and 1103 liters respectively. RK PrintCoat Instruments K Hand Coater applies paints, inks, lacquers, adhesives and coatings to paper, board, plastic film, foil, metal, glass and wood, depositing wet films from 4 to 500 μm. The manual K Hand Coater uses color-coded stainless-steel K-bars and can apply two or more coatings side by side in one operation for direct comparison. The K Control Coater regulates application speed and pressure using wire-wound bars or gap applicators; its two models cover areas up to 170 × 250 mm or 325 × 250 mm at standard speeds of 2–15 m/min. The KPP gravure coating and printing machine handles films, paper, board, aluminum foil and PVC at printing speeds up to 40 m/min, with micrometer-based pressure adjustment and a 400 × 500 mm workbench footprint. KPP supports printing two or more inks for comparison, registered overprinting and, after replacement of the printing head, flexographic and laminating proof trials. Esiproof manual flexographic proofing equipment uses single-screen or banded ceramic anilox rollers for commercial inks and substrates; its compact design suits on-site troubleshooting. The Flexiproof 100/UV flexographic proofing press produces test prints on paper, film and foil for ink color matching, quality control and tests of abrasion resistance, scratch resistance, flexibility, durability and gloss.
Company profile
PROCHEM PACIFIC CORPORATION specializes in the sale, maintenance and calibration of instruments used to measure color, light sources and weathering. Its equipment portfolio covers Konica Minolta color and appearance measurement instruments from Japan, Q-LAB weathering testers from the United States and RK PrintCoat Instruments laboratory coating equipment from the United Kingdom.